The Camouflet Convector V2 and Super Capacitor

Camouflet’s New, Improved Gear!

Introducing two new vapes form Camouflet (save 5% with code “troyandjerry”) – the Convector V2 and the Super Capacitor. Technically the Super Capacitor is a new heater for the Convector XL, but it feels like a new vape! The V2 has a larger bowl than the original Convector, so it’s mid-sized between the original Convector and the XL model.

So far the results have been great. I prefer these vapes with the Camouflet Inductor, but they work well with a torch lighter or a standard induction heater. Let’s get into how these vapes work…

It’s Like a Silent, Convection VapCap

Camouflet’s Convector gets its name from it’s heater, designed to be full convection. Heat it up just like you would any vapcap. I used a DynaVap Apollo 2 Induction Heater with it exclusively for its consistency – it heats the same every time. Then I used the Inductor heat system (save 5% with code “troyandjerry”) and the heat up time was incredible! The main difference between this and a DynaVap is the lack of a click. I would say the convection hits are really different, too, but maybe not so much compared to the Helix tip. We’ll compare those tonight on the livestream to find out!

The Convector is a manual dry herb vape experience that works really well for those that like to ride past the click on the DynaVaps. If you don’t have an induction heater that flashes as it heats (like the Ispire Wand), you’ll need to keep a count rolling in your head so you don’t overheat it and burn your herbs.

The Convector is available in stainless steel or titanium (titanium on the right in the pic above), and the heat is definitely convective. The abv comes out light most of the time, and it’s pretty forgiving if you overheat it, since most of the cook is during your draw.

The Induction Ecosystem

Check out the Inductor heating station! It has a detachable workspace, power controller, and an induction heater that doesn’t work like all the others.

Camouflet has figured out how to make an induction zone that isn’t a typical induction coil. Instead of sticking your vape into a hole to heat up, they have a zone that you can just put the vape in to heat it up. Touch the button to the Convector heater and press the heat button, and pull away when it’s ready!

Tips and First Impressions

But here are some initial thoughts and tips for the Convector.

• The heater is in the very end of the cap, so make sure that part is in the heat zone of your induction heater. If that part doesn’t get hot, the hit will be off.
• That little ring around the stem is important. I don’t know why, but the stem is much cooler behind that ring where the parallel lines are. It feels like an old school joint pinch.
• If you overheat it, you can let it cool before it cooks the load too much. The part near the heater will still suffer, but the rest of the load stays pretty fresh. In this stream we’ll see if it still works when you blow into it to cool it down.
• Works great on any DynaVap compatible stem! Go at it with your faves.

The Gallery

Here’s some eye candy for you!

The Convector comes in a nice bamboo tube with a subtle brand on its side.

On the left is a stainless steel Convector ready to go. On the right is a titanium stem without the tip and cap.

Same picture from a different angle!

Complete stainless steel unit on the left and a titanium stem on the right.

The back end of the stem has parallel grooves on it. This is the best place to hold it. Somehow the stem stays cooler in that part.

And when you hold it right, it feels like an old school joint with that distinctive pinch.

The Convector exploded into all three parts – cap, tip and stem. Pretty simple.

The 14mm water pipe adapter on a bubbler. I had to use an 18mm/14mm reducer for this glass piece.

The tip has two o-rings for a connection, and it’s very easy to take on and off.

Here’s a look up the bunghole of the tip. You can see the underside of the screen.

Looking into the bowl at the other side of the screen. The screen isn’t removable.

The top of the tip. Those holes are the fresh air intakes.

A look into the cap at the underside of the heater.

The Convector in my DynaVap Apollo 2.

Here I put the tip on a Simrell blackwood stem without an airport. The Convector Stem doesn’t have an airport, so I went without, as well.